Porsche Panamera G1 (970) Compressor level control air suspension

Porsche Panamera G1 (970) Compressor level control air suspension Porsche Panamera G1 (970) Compressor level control air suspension Porsche Panamera G1 (970) Compressor level control air suspension Porsche Panamera G1 (970) Compressor level control air suspension Porsche Panamera G1 (970) Compressor level control air suspension Porsche Panamera G1 (970) Compressor level control air suspension Porsche Panamera G1 (970) Compressor level control air suspension
  • Short supply
  • Item no.: KKK0-R0OE-PANA
  • Shipping weight: 6,00 kg
  • Product weight: 6,00 kg
  • Shipping time: 4 - 6 workdays
  • starting from : 699,00 €
  • including 19% VAT., plus shipping (Paket)
  • Recommended retail price: 1.386,00 €
  • You save 50%, that is 687,00 €
Loading ...

  • Deposit
Category:

Description

With this offer you get an original Continental compressor (Porsche Active Suspension Management PASM), which is technically as visually as good as new - Made in Germany.
The unit was completed with the original elements with the original elements such as holder, suspension elements, sensor and housing at Miessler AutomotiveŽ.
.
With a Miessler AutomotiveŽ overhauled compressor you get a product that was produced by the original manufacturer Continental.
Thanks to our many years of experience in this field, we can ensure that the technical condition of the compressor is in no way inferior to that of the car manufacturer's new compressor.
.
Depending on requirements, we use identical wear parts such as
- ball bearing
- sealing rings
- PTFE piston ring
- completely new connecting rod
- carbon contacts
- electrical plugs
- compressed air connections
- cylinder sleeve
- complete dryer unit
.
Can be installed in the following vehicles:
Porsche Panamera 970 (G1) 2009-2016
.
Original spare part number:
97035815126, 97035815112, 97035815125, 97035815122, 97035815124, 97035815111, 97035815110, 97035815109, 97035815108, 97035815107
.
Scope of delivery:
Compressor aggregate
Relay
.
CAUTION: The replacement of the relay is mandatory, otherwise the warranty on the compressor is forfeited!
Relay must be replaced at the same time as the compressor change
.
Attention!!!
The vehicle suspension is based on a combination of electronically controlled level control and bellows filled with nitrogen 5 or CO2.
The gas pressure in the system MUST only be rebuilt after replacing any spare parts (such as compressor, valve, air spring and/or suspension strut) according to the vehicle manufacturer's specifications.
At this point the compressor is NOT used to refill the system.
These Continental compressors, or the corresponding Miessler Automotive Aftermarket compressors, serve exclusively for pressure compensation in the closed system.
If you do not follow the installation instructions of the vehicle manufacturer, the compressor may quickly be damaged, resulting in loss of warranty.
.
The complete emptying of the system is the general specification of the car manufacturer for repairs to the spring system.
After replacing the corresponding spare part, the system MUST be refilled with CO2 or nitrogen 5 according to the vehicle manufacturer's instructions.
This can only be done with appropriate software and special tools.
Only then can you start further steps, such as calibration or commissioning of the level control.
.
Before purchasing a compressor, please note the following:
The most common reason for a defective compressor is a leak in the system, causing the compressor to run too long and too often.
An excessive number of switch-on cycles will cause the relay contacts to stick together.
As a result, the relay no longer functions.
The result is continuous current on the compressor.
The compressor runs continuously without control until it burns out.
Before a new compressor is installed, all the reasons why it has been damaged must be completely eliminated.
.
To the leak:
A leak can occur in many places, for example:
- Porous or damaged air springs or air spring parts (strut)
- Worn seals, defective compressed air connections and chafed compressed air hoses
- Leaky housings in components such as compressors, valves, air springs or suspension struts.
.
Every air spring system is vulnerable in this way.
Therefore, follow our advice to avoid any further repairs in the near future.
.
Basic advantages why you are in good hands with Miessler AutomotiveŽ when it comes to air suspension:
- We have been dealing with this topic since 2003
- Manufacturer selected by us is one of the supporting pillars for best quality
- Close cooperation with manufacturers in the field of quality management
- More and more own products that facilitate the repair of your vehicle
- Repair service in our own specialist car workshop.
.
Our technical advice for the air supply device:
1. Change the relays before installing the compressor even if it seems to still work.
This is also a specification by the car manufacturer. Be sure to change the right relays.
Relays look similar, that is why there is a risk to change the  wrong relays.
2. Be sure to check whether the system is leakproof after repairing.
The easiest way to do this is to park the vehicle. Wait for the system to automatically re-adjust if your car has this feature.
Then measure the heights from the ground to the lower edge of the fender as exactly as possible and take notes.
On the day after measure these heights  again and compare them with the ones before. Even a small difference will lead to a damaged compressor and damaged valves in the long run.
.
When driving with a leaking suspension for a long time it needs to be assumed that the compressor is running more often than normal. The increased number of cycles of powering on and off is likely to already have damaged the compressor.  Depending on the duration of that condition you should change the relays and check the performance of the compressor to be on the safe side. After the vehicle stood overnight the compressor normally doesn't need to run more than 20 to 30 seconds for the system to be ready to start.

Recommend item

Contact information